Skip to content
Robotics

G1 thermal safety filters

защита от падений и перегрева для робота Unitree G1

2 min readupdated

Набор из трёх фильтров безопасности на базе world-моделей (нейросетей, предсказывающих развитие событий в среде) для симуляции гуманоидного робота Unitree G1 в MuJoCo Warp и mjlab. На каждом шаге управления (50 Гц) фильтр проверяет действие основной политики: если прогноз показывает риск падения или нагрев обмотки любого мотора выше 70 °C, управление передаётся резервной политике, обученной методом SHAC (алгоритм обучения с подкреплением через дифференцируемую симуляцию). В отличие от обычных контроллеров, эти фильтры учитывают тепловую модель двигателей и используют конформную калибровку границ безопасности. Релиз пригодится исследователям в области робототехники и обучения с подкреплением (RL) для безопасного тестирования алгоритмов локомоции в симуляторе.

Ключевые особенности

  • Три варианта архитектуры: joint (одна сеть предсказывает и движение, и температуру), separate (движение предсказывает сеть, а температуру точно считает физическая модель sysID) и fall_only_cbf (сеть следит только за падениями, а перегрев отсекает барьерная функция управления CBF).
  • Автоматическая проверка совместимости: при запуске загрузчик сверяет хэши файлов по manifest.json и проверяет соответствие параметров среды через check_binding.
  • Заметный рост выживаемости при толчках: при трекинге движений с политикой SONIC доля успешных эпизодов выросла с 47.6% до 88.5% в режиме separate с защёлкой (latch).
  • Снижение перегрева: доля эпизодов с перегревом моторов в том же тесте упала с 19.3% до 0.9%.

Что можно сделать

  • Встроить фильтр как обёртку WMTubeFilteredEnv в пайплайн обучения on-policy алгоритмов (например, PPO) в среде robot-safety-sandbox.
  • Запустить готовые эксперименты по обучению ходьбы G1TP-Track-Walk4-WM-* из репозитория g1_safety_porl для сравнения трёх подходов к безопасности.
  • Откалибровать границы безопасности под собственную политику управления с помощью скриптов calibrate_wm_min_tube.py из песочницы.

Пример

from robot_safety_sandbox.filters.pretrained import download, load_pretrained_filter
from robot_safety_sandbox.filtered_env import WMTubeFilteredEnv

root = download("zengyh29/g1-thermal-safety-filters")
env.reset()
filt, bundle = load_pretrained_filter(env, root, "separate", seed=0, condition="wmmin:1:0.95+dwell1")
env = WMTubeFilteredEnv(env, filt)
ПодробнееБенчмарки (трекинг SONIC с толчками, 3 сида × 1024 эпизода): выживаемость без фильтра — 47.6% (19.3% перегревов), с фильтром separate (wmmin:1:0.95+latch) — 88.5% (0.9% перегревов).
Требования: mjlab (коммит dcdf6ce5), MuJoCo / MuJoCo Warp 3.16.0, PyTorch с CUDA, robot-safety-sandbox, safety_sb3 и G1-robot-model-with-SysID 0.4.0.
Ограничения: работает только в симуляции, так как world-модель использует привилегированные данные (точные состояния суставов, контакты стоп и температуры); горизонт 3 с не опубликован.
Discuss Telegram 0

Will it run?

Working out the memory needs

The bot is still collecting this model's weight sizes; the estimate will appear here in a few minutes. Meanwhile you can rent a GPU with headroom.

Massed ComputeOpen Massed Compute

Run it on Massed Compute

The script downloads the model to the rented machine. How to run it is in the model card.

  1. 1. Rent a machine with a fitting GPU

    Open Massed Compute
  2. 2. Paste the script into the machine's terminal

    Connect over SSH (the Massed Compute panel shows the command) or open a terminal on the machine's desktop.

    HF_TOKEN / CIVITAI_TOKENThe script starts with token lines: paste yours between the quotes. The Hugging Face token is for gated models, the Civitai one for Civitai models.

    # zengyh29/g1-thermal-safety-filters
    mkdir -p ~/models
    curl -LsSf https://astral.sh/uv/install.sh | sh
    source "$HOME/.local/bin/env"
    uv tool install "huggingface_hub[cli]"
    hf download zengyh29/g1-thermal-safety-filters --local-dir ~/models/g1-thermal-safety-filters
    # The model is in ~/models. How to run it is in the model card (link above).
  3. 3. Use it

    The model is in ~/models. How to run it is in the model card (link above).

Stop the machine in the panel when you are done: it bills by the minute while it runs.

How to speed it up

Picked for this model type. Choose your hardware above to see what fits you exactly.

  • FlashAttention 44.0.0b40from November 18, 2026new release

    fastest exact attention on B200

    Kernels for Blackwell (beta). Exact attention without quantisation — fine for everything, LLMs included.

    How to enable: pip install flash-attn-4; vLLM and SGLang pick it up themselves.

    Earlier generations (2)
    • FlashAttention 3 — The Hopper (H100/H200) version with FP8.
    • FlashAttention 2 — The standard for RTX 30/40/50 and A100: exact attention without the memory cost of long contexts.
  • torch.compile2.15.0from October 28, 2026new release

    10–30% for free

    Compiles the model for your GPU. Slower first run, faster afterwards.

    How to enable: model = torch.compile(model); in ComfyUI the TorchCompileModel node.

Model family

New posts about versions of g1-thermal-safety-filters (quants, finetunes, LoRAs) will show up under the bell.

No known relatives of this model yet. All derivatives on Hugging Face

About the model

zengyh29/g1-thermal-safety-filters
Author
zengyh29
Category
Robotics
Released
Posted

On NeyroLearn

Hugging Face

00

Ask AI about this model

Answered by Gemini 4 · the chat is kept only in this tab

Comments